Top 10 common forklift mishaps ， forklift operation ought to take note of these matters ！.

Top 10 common forklift mishaps ， forklift operation ought to take note of these matters ！.

Blog Article

Do not undervalue the forklift at work. If the operation is bad, there will certainly be significant accidents in minutes, and there are many accidents including forklifts.

Situation 1: The forklift cargo blocked the motorist's view, and the individual in front might not be discovered, causing a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost caused casualties.
Instance 3: The size of the forklift freight surpasses the allowable width of the course and holds on the roadside rack, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift vehicle driver did not observe the pedestrian, and the pedestrian did not observe the forklift.
Case 6: The forklift lifts the workers illegally, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not put on a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.

Beginning.
1. Before beginning, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be safe prior to beginning.
3. When the forklift starts with a lots, the chauffeur needs to first validate that the tons is secure and trustworthy.
4. The beginning needs to be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the job site or while driving, beware that there will certainly be no obstacles overhead. When the lots is traveling, the fork needs to not be elevated too high, which will influence the security of the forklift. .
3. After unloading, the fork ought to be decreased to the normal driving position before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal ought to be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will trigger the lorry to shed lateral stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to shut off the fire and slide, and it is restricted to brake suddenly while driving with loads unless there are unique circumstances.
6. When the forklift is running, it should obey the traffic rules in the factory and should keep a specific security distance from the automobile in front. .
7. When the forklift is running, the tons needs to remain in the lowest setting that does not impede the driving, and the gantry must be appropriately slanted back. The tons shall not be raised except when stacking or loading. .
8. The elevation of the lots have to not obstruct the motorist's view. In special situations, when the item affects the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving speed of the forklift in the factory area is 5 km/h, and it has to drive securely at a low speed when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is prohibited for workers to stand on the fork to hold things and play a stabilizing role. .
12. If troubles are discovered, they will be fixed and reported in a timely manner, and they will certainly never operate with ailments or hide them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with a single fork or utilize a fork top or pull. In unique situations, safety and security warning signs must be established to advise surrounding pedestrians. .
3. In the process of loading and discharging items, the forklift needs to be braked with the brake. .
4. The rate of the vehicle must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled things and harm individuals. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it needs to be noted that the fork pointer ought to not touch various other items or objects. The lots needs to be stabilized with very little back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted onward slightly when the tons is reduced to permit easy placement of the lots and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and harm individuals. .
8. Straining is restricted, and it is forbidden to make use of forks to raise employees to engage in high-altitude operations to prevent high-altitude falling mishaps. .
9. It is not enabled to make use of the brake inertia to slide, place, round or roll things. .
10. It is not allowed to use forks to pick, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique scenarios, such as the motorist does not leave the automobile's view and does not go beyond 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the appearance ought to be checked, and fuel, lubing oil and air conditioning water must be added.
2. Inspect the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are complete and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature level are regular.
5. After the forklift is running, the outside leakage needs to additionally be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to inspect before leaving the car;.
2. When you run into a person in front of you throughout driving, you must send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m in the air;.
5. The turning ought to not be also sharp to avoid the tendency of " cost-free turning";.
6. Adding and down the incline should be slow-moving and uniform, and no activating the slope is allowed.
7. Do not drive throughout the gradient. When the slope is greater than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift employees bring the goods and move forward, if they come across large or hefty goods and go to the driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance Electric Forklift Truck for Warehouse driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not allowed under the following conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of Electric Forklift Truck for Warehouse the area with the very same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844